Terms and Conditions

  1. Installation Work:
    1. All electrical installation work will comply with BS7671:2008(2011) and any amendments in force at the time of the works.
    2. All electrical installation work will comply with applicable Building Regulations in force at the time of the works.
    3. Electrical Installation and Minor Works certificates and Building Regulations notifications issued by RMD Electrical Ltd cover only those works installed by RMD Electrical Ltd.
    4. Where work is to extend or modify existing circuits, costs quoted assume existing circuits are safe and are in an adequate condition. Any work required to bring these circuits up to standard will be at additional cost.
    5. No addition or alteration will be carried out to rubber insulated (VIR) cables.
    6. Where carpet or floor coverings require lifting, best endeavours will be made to avoid damage and to refit to an acceptable standard. However, employing a specialist fitter may be prudent, to effect a fully satisfactory reinstatement.
    7. Unless agreed beforehand, chases to walls, etc will be left unfilled. Final finishing of skim coat plaster and final decoration is excluded.
    8. RMD Electrical Ltd will endeavour to undertake installation work to a clean standard. However, some additional vacuuming and cleaning down of surfaces should be expected afterwards. Any equipment susceptible to damage from dust (eg video or computer equipment) must be removed from the work area prior to RMD Electrical Ltd’s arrival.
  2. New Consumer Units:
    1. Installation of new consumer units (fuse board) is subject to the whole installation being tested to ensure it is safe to be connected to a new consumer unit. This is a legal requirement under Part P Building Regulations. The basic cost for this is included in the installation cost.
    2. Any faults found during the above testing which are deemed unsafe, must be rectified prior to that circuit being reconnected to any new consumer unit. Any costs for such work are not included. Such issues will be brought to the clients attention as soon as it is practical during work.
    3. In particular it may be necessary to install new main services bonding to water, gas or oil supplies. This is especially common on properties built during or prior to the early 1970s and again these are at additional cost unless agreed otherwise beforehand.
  3. Exclusions:
    1. Whilst we try to be as helpful as possible and will generally do some limited moving to create access, the clearing and / or moving of furniture and other items blocking access to work areas are not included within the quote.
    2. Whilst RMD Electrical will try and ensure that electrical items are plugged back in and in working order before we leave the premises, we will not be held responsible for any losses due to any electrical item not being plugged back in and / or switched on.
    3. Removal from site and disposal of rubble, materials, general waste and packaging is not included. RMD Electrical may, at their discretion, remove old fittings and wiring for responsible disposal.
  4. Pricing:
    1. Estimated costs assume continuous and unhindered access to the site by prior arrangement with the client.
    2. Unless stated otherwise, the costs quoted assume standard working hours between 08:00hrs – 16:30hrs Monday to Friday inclusive. Work required by the client outside these hours may attract premium rates although we will try and be flexible.
    3. Additional work not covered in stated costs will attract an additional charge plus materials.
    4. Estimates are valid for 30 days from the date of the estimate.
  5. Risk and Title of Goods:
    1. The risk in all goods supplied shall pass to the Client upon delivery.
    2. All goods supplied shall remain the property of RMD Electrical until all sums due have been paid in full.
  6. Warranty:
    1. RMD Electrical Ltd warrants its installation work to be defect free for a period of twelve months from the invoice date. Cover does not extend to goods supplied by others, physical damage, willful misuse or instances where the installation has been altered or tampered with by third parties. The warranty also excludes fair wear and tear, lamps, fuses or other consumables.
    2. Where projects involve works by third party trades, any damage to the electrical installation by third parties shall remain the responsibility of the Client. Any rectification costs must be paid by the Client prior to commencement of a second fix. Recovery of such costs from any third party shall be the Clients responsibility.
    3. Security alarms will be fitted with a tamper seal on the main panel. All warranty is void if this is broken. Request of engineer code will also void any warranty
  7. Payment:
    1. Unless agreed in writing, payment in full should be made on completion of the specified works to RMD Electrical Ltd.
    2. Larger projects may require a deposit before work, as stated in estimate (if applicable).
    3. Where projects involve separate first and second fix works, part payment may be due on completion of the first fix (see quote for more details). 
    4. Payment is accepted by cash, bank transfer or cheque.
    5. In the event of any non payment RMD Electrical Ltd reserve the right to withhold any certificates for work carried out until such payments are made.
  • “In an age where mediocre service seems to be standard practice, it was a pleasant change to find a company with such great standards. I can honestly say that I will certainly ask for a quote from you before I try anyone else.”

    Senior Site’s Manager | Commercial
  • “Brilliant professional service by very professional people. Will definitely use them again!”

    Residential
  • “The service we have received from RMD for the last 3 years has been second to none. I would not recommend another electrical contractor.”

    Commercial
  • I have been a client of RMD Electrical for nearly 10 years, with them
    working as both sub-contractor and main contractor. They have delivered many different
    types of work for me in this @me and I have always received an excellent service especially
    on some of the more challenging jobs. I would highly recommend RMD.

    B Thompson | Bromford Building Surveyor
  • “RMD sent an electrician to our home – he arrived on time and carried out the required repairs. I was impressed by the high standard of the work which was done quickly and efficiently”

    Residential

Why Our Customers Choose Us

Comprehensive
Project Planning

All Works
Warrantied

Approved
Contractor

Let’s work together.

To discuss next steps and posible solutions available to you:

© RMD Electrical Ltd.
All rights reserved